Ver Investigador - - Prisma - Unidad de Bibliometría

Eduardo Sánchez Caballero

Profesor Sustituto Interino
esanchez3@us.es
Tipo Año Título Fuente
Capítulo2021 Determinación de la dureza de los compactos de TI-AL sinterizados mediante resistencia eléctrica y preparados a partir de polvo amorfizado mediante molienda mecánica Sinergias en la investigación en STEM
Otros2021 Ensayos no destructivos Portal De Realidad Extendida de la Universidad de Sevilla
Otros2021 Medición, calibración y control de calidad. Portal De Realidad Extendida de la Universidad de Sevilla
Otros2021 Operaciones de mecanizado Portal De Realidad Extendida de la Universidad de Sevilla
Otros2021 Procesos de soldadura Portal De Realidad Extendida de la Universidad de Sevilla
Ponencia2020 HTML como herramienta interactiva para solucionar problemas de ingeniería: Aplicación en diagramas binarios de equilibrio II Congreso Internacional de Innovación Docente e Investigación en Educación Superior: Avanzando en las Áreas de Conocimiento
Artículo2020 Influence of processing parameters on the conduct of electrical resistance sintering of iron powders METALS
Artículo2020 Influence of temperature on mechanical properties of AMCs METALS
Otros2020 LABORATORIO DE INGENIERÍA Y CIENCIA DE LOS MATERIALES EN REALIDAD VIRTUAL Portal De Realidad Extendida de la Universidad de Sevilla
Artículo2020 Modelling and Simulation of the Electrical Resistance Sintering Process of Iron Powders METALS AND MATERIALS INTERNATIONAL
Artículo2020 Nickel porous compacts obtained by medium-frequency electrical resistance sintering MATERIALS
Capítulo2019 Amorfización de aleación Ti40CU60 mediante molienda mecánica Avances en la investigación en ciencia e ingeniería
Artículo2019 Amorphous Al-Ti powders prepared by mechanical alloying and consolidated by electrical resistance sintering METALS
Artículo2019 Consolidation by MF-ERS of mechanically alloyed Al powder JOURNAL OF ALLOYS AND COMPOUNDS
Artículo2019 Crystallisation of amorphous Al-Sm-Ni-(Cu) alloys INTERMETALLICS
Artículo2019 On the Densification Kinetics of Metallic Powders Under Hot Uniaxial Pressing METALS AND MATERIALS INTERNATIONAL
Ponencia2018 Amorphous phase formation and heat treating evolution in mechanically alloyed Al-Ti powders Key engineering materials
Artículo2018 In Situ Synthesis of Al-Based MMCs Reinforced with AlN by Mechanical Alloying under NH3 Gas MATERIALS
Ponencia2018 Medium-frequency electrical resistance sintering of highly oxidized iron powder Key engineering materials
Artículo2018 Medium-Frequency Electrical Resistance Sintering of Oxidized CP Iron Powder METALS
Artículo2018 On the compressibility of metal powders POWDER METALLURGY
Ponencia2018 Production of aluminium based MMCs by short-time ammonia gas flow milling Key engineering materials
Artículo2017 A Method to Determine the Electrical Resistance of a Metallic Powder Mass under Compression METALS
Artículo2017 Phenomenological equation for the thermal dependence of the activation energy of creep MATERIALS LETTERS
Artículo2017 Synthesis and characterization of in situ-reinforced Al-AlN composites produced by mechanical alloying JOURNAL OF ALLOYS AND COMPOUNDS
Artículo2016 A new method for synthetizing nanocrystalline aluminium nitride via a solid-gas direct reaction POWDER TECHNOLOGY
Ponencia2016 Fabricación y caracterización de núcleos magnéticos de aleaciones amorfas mediante ruta pulvimetalúrgica simple y económica III Jornada de investigación y postgrado: Libro de Actas
Artículo2016 Improvement in the Mechanical Behavior of Mechanically Alloyed Aluminum Using Short-Time NH3 Flow METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
Artículo2016 Influence of Milling Atmosphere on the Controlled Formation of Ultrafine Dispersoids in Al-Based MMCs METALS
Ponencia2015 High Temperature Behavior of Nanostructured Al Powders Obtained by Mechanical Alloying under NH3 Flow 4TH INTERNATIONAL CONGRESS IN ADVANCES IN APPLIED PHYSICS AND MATERIALS SCIENCE (APMAS 2014)
Artículo2014 Nanocrystalline Al Composites from Powder Milled under Ammonia Gas Flow ADVANCES IN MATERIALS SCIENCE AND ENGINEERING
Ponencia2013 Direct aluminum powder nitridation under flowing ammonia Materials Science and Technology Conference and Exhibition 2013, MS and T 2013
Ponencia2013 Influence of Composition on Pitting Corrosion of (MA)-Al Reinforced with Carbides and Nitrides 3RD INTERNATIONAL ADVANCES IN APPLIED PHYSICS AND MATERIALS SCIENCE CONGRESS
Ponencia2013 On the Sintering Conditions of CP Titanium Powder 3RD INTERNATIONAL ADVANCES IN APPLIED PHYSICS AND MATERIALS SCIENCE CONGRESS
Ponencia2013 Order Effect of Vacuum and Ammonia Atmospheres on Aluminium Nitriding by Mechanical Alloying Materials Science Forum
Ponencia2013 Titanium powder milled under argon atmosphere. Effects of sintering conditions Materials Science and Technology Conference and Exhibition 2013, MS and T 2013
Ponencia2013 Use of Short-Time NH3 Gas Flow During Al Milling 3RD INTERNATIONAL ADVANCES IN APPLIED PHYSICS AND MATERIALS SCIENCE CONGRESS
Artículo2011 Strengthening of ultrafine PM aluminium using nano-sized oxycarbonitride dispersoids MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
Ponencia2011 Use of urea and ammonia to produce high-strength PM aluminium parts Proceedings of the Euro International Powder Metallurgy Congress and Exhibition, Euro PM 2011
Artículo2007 Derechos humanos y acceso universal a la energía Eco Sostenible
Artículo2006 La ayuda oficial española al sector de la energía: demasiadas condiciones Cuadernos internacionales de tecnología para el desarrollo humano
Ponencia2004 Laboratorios docentes de la Facultad de Informática de la UCM: un modelo para la gestión integrada de aulas informáticas En apoyo del aprendizaje en la universidad : hacia el espacio europeo de educación superior
Artículo1994 Centro de salud en Palomarejos, Toledo AV Monografías

Proyectos de Investigación

Fecha de inicio Fecha de fin Rol Denominación Agencia financiadora
01/01/2016 31/12/2019 Investigador/a Fabricación de Núcleos Magnéticos Amorfos Mediante Molienda Mecánica y Sre-Mf (DPI2015-69550-C2-1-P) Ministerio de Economía y Competitividad (Nacional)
01/01/2010 31/05/2013 Investigador/a Nuevo método de producción de piezas de aluminio nanoestructurado mediante mecanosíntesis en flujo de amoniaco gaseoso (DPI2009-08291) Ministerio de Ciencia e Innovación (Nacional)
El investigador no tiene ningún resultado de investigación asociado